Planex SWP-0208G User Manual

1 SWP-0208G

102.1.2 Ports Port status page always shows current port status of all 8 ports. User can set link mode, enable or disable flow control and jumbo fr

112.1.3 Port-based VLAN Port-based VLAN is a kind of VLAN which is a group of ports marked as a kind by group ID, different VLAN ( different ID ) can

122.1.4 Tag-based VLAN Tag-based VLAN is another kind of VLAN which is a group of ports marked as same kind by assigning a tag-value on each port, sa

13If VLAN 10 and VLAN ID 20 must be isolated, then user must delete member port 5,6,7,8 in default VLAN group( VID = 1 ). See below Be aware

14 1. VLAN Aware mode: Enable – When Tag-VALN function is applied on this port, user may enable VLAN Aware associated with this port, then ingres

15 2.1.5 Port Trunking A default diagram is shown below, and up to 4 groups are provided Choose and click the trunk ports you want to g

16

172.1.6 Port Mirroring A default diagram is shown below, Choose and click the ports you want to monitor, for example, choose port 2 is mirro

182.1.7 Quality of Service There are 4 class priority can be set for each port: Low, Normal, Medium and High, because there are 8 priority levels ( 0

19 When user choose the 802.1P priority, this means frames are with VLAN Tag inside the switch, the priority in the Tagged frame ( 2 bytes Tag

2 SWP-0208G, 8+2SFP 8-Port Gigabit Web Smart Switch User’s Manual Version: 3.4 April 1, 2008

20 2.1.8 Storm Control A default diagram is shown below, Choose and click type of storm you want to control, for example, choose Broadcast st

21 Two parameters need to be set per port basis in this webpage:  Protocol Enabled – to enable/disable LACP protocol for a port.  Key Val

222.1.10 RSTP The Spanning-Tree Protocol (STP) is IEEE 802.1d standardized method for avoiding loops in switched networks. Enable STP to ensure that

23Use the following parameters in the webpage to configure RSTP function:  System Configuration ¾ System Priority – A value to identify the root

242.1.11 IGMP The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IGMP can manage the multicas

25 2.1.12 802.1x A default diagram is shown below, user must contact the manager of RADIUS server, and then get IP, UDP port number ( usually f

26

27 2.2 Monitoring 2.2.1. Port Statistics Choose and click command manual, after execution, diagram will shown below, user can clear counter or refres

282.2.2 LACP Status Choose and click command manual, after execution, diagram will shown like below, user can refresh as will

292.2.3 RSTP Status Choose and click command manual, after execution, diagram will shown like below, user can refresh as will 2.2.4 IGMP Status Ch

3TABLE OF CONTENT 1.0 INTRODUCTION ...

302.2.5 Ping Fill up the IP address you want to ping, set Time Out time and Counts, for example, IP = 192.168.1.141, count = 5, time pout =

312.3 Maintenance 2.3.1 Warm Reboot Choose and click command manual, diagram will shown like below, user can press Yes or No Warm Reboot Are you su

322.3.4 Config File Choose and click command manual, diagram will be shown, and then direct the location of the file that is to be backup, give a na

33 Key in “ Command “ and then key in “ ? “, second level will be shown , for example

34If user wants to check the IP related information, he may do as below All other function can be operate likewise. Type “ up “ or “ / “

41.0 Introduction This web smart switch is a high speed switch that provides up to 8 10/100/1000Mbps copper Ethernet ports, besides, it provides many

5 Support “relocate port number” to “ http operation “  Port trunk with fail-over capability  Support flow control for both full/half duplex op

61.2 Start to Manage This Switch Either way user may start to manage this switch, web mode through Ethernet port or terminal mode through RS232 port.

72.0 Web management After login is successfully validated, the switch’s home page will show up. The left part on the page provides the function men

82.1 Configurations 2.1.1.1 System information The system diagram shows general common system information, they are H/W, F/W version, MAC address,

92.1.1.2 DHCP The default DHCP is off, so Default IP or user defined IP is used when this machine is turning-ON, but if this switch needs an IP assig